This standard is issued under the fixed designation D ; the number 1 This test method is under the jurisdiction of ASTM Committee D on Rubber. ASTM D is an abrasion method used for coated materials and is cited for classification testing by the ANSI standard. ASTM D Abrasion resistance tests are intended to measure the wear resistance properties of a material. This may be correlated to expected end use.
|Published (Last):||10 September 2004|
|PDF File Size:||8.73 Mb|
|ePub File Size:||15.56 Mb|
|Price:||Free* [*Free Regsitration Required]|
Thin, Hard, Dense Deposit This specification covers the engineering requirements for the deposition of a thin, hard dense chromium coating on surfaces of ferrous and non ferrous alloys and the properties of the coating.
Applications of high pressure decorative laminates covered by this D33389 include wait stations, service counters, and other counters when used in conjunction with cutting boards or other means of preventing direct food contact with the laminate. This test method covers the determination of the resistance to zstm of fabrics coated with rubber or plastics.
Taber Abrasion ASTM D D D
NASTA Manufacturing Standards and Specifications for Textbooks If offset printed on coated cover material, a protective top coating for abrasion resistance is required. This European Standard specifies the functional requirements and test methods for wash basins for domestic purposes. Fabric samples are mounted flat and rubbed in a figure eight like motion using a piece of worsted wool cloth as the abradant.
The resistance to abrasive damage is judged qualitatively by its effect on the legibility, pattern, and color of xstm graphic marking.
These practices cover the selection and use of procedures for testing polymeric powders and powder coatings. This International Standard awtm a general method for determining the resistance to abrasive wear of plastics under the action of abrasive wheels.
ASTM C Standard Specification for Prefaced Concrete and Calcium Silicate Masonry Units This specification covers prefaced concrete masonry units with the exposed-to-view-in-place surfaces covered at the point of manufacture with resin, resin and inert filler, or cement and inert filler to produce a smooth resinous tile facing.
This specification covers the engineering requirements for the deposition of a thin, hard dense chromium coating on surfaces of ferrous and non ferrous alloys and the properties of the coating. This part of ISO specifies a method for determining the resistance to abrasion of a dried film of paint, varnish or related product, using dd3389 paper attached to wheels and abrading by making a rotary d33389.
It is applicable to all low pressure overlaid particleboards and medium density fibreboards MDF’s.
This guide provides a common basis atm which protective coatings for the surfaces of light water-moderated nuclear power generating facilities may be qualified and selected by reproducible evaluation tests.
The purpose of this test is to quantify the haze, luminous transmittance, and abrasion resistance properties of the primary lens material of a full facepiece RPD. See tests 12 and EN Resilient floor coverings – Determination of wear resistance – Part 2: To determine the abrasion resistance of chemical coated fabrics and films using a rotary platform double head tester.
Standard Test Method for Coated Fabrics Abrasion Resistance (Rotary Platform Abrader)
The values given in parentheses are for information only. This specification covers prefaced concrete masonry units with the exposed-to-view-in-place surfaces covered at the point of manufacture with resin, resin and inert filler, or cement and inert filler to produce a smooth resinous tile facing. This method specifies the testing methods for determination of abrasion resistance of rubber, vulcanized or thermoplastic hereafter referred to as “vulcanized rubber”.
Association of Contact Textiles Website. This Standard applies to high pressure decorative laminates for use as work and nonwork surfaces of food service equipment on which direct food contact during normal preparation or holding operations is not intended, expected, or reasonable. This may be correlated to expected end use performance.
My go to reference on the subject is the Association for Contract Textiles. BS EN Surfaces for sports areas – Determination of resistance to abrasion of non-filled synthetic turf This document describes a method for the determination of the wear resistance of a non-filled synthetic turf surface using an abrasive wheel under laboratory conditions.
C3389 test shall be used to give an indication of the comparative wear characteristics of painted, printed or hot embossed finishes, to plastic substrates. This specification covers the materials and physical characteristics of plates, tags and bands astmm devices used for identification of equipment. This guide is intended to assist in establishing procedures for determining the relative resistance f3389 treated or untreated mortar surfaces.
Behavior at Abrasion in German DLA1 Determination of Resistance to Surface Wear This Appendix specifies a method of measuring the ability of the surfaces of decorative laminated d33389 to maintain their original design or colour under abrasive wear. The number of cycles that the fabric can endure before fabric shows objectionable change in appearance yarn breaks, pilling, holes is counted.
Number of cycles determines abrasion rating. This Japanese Industrial Standard applies to building materials and parts of building construction and specifies the testing method to evaluate the degree of abrasion of the test piece. EN Wood flooring – Test methods to determine elasticity and resistance to wear and impact resistance This document specifies two alternative test methods to determine the resistance to wear of lacquered wood floorings and one method to test the elasticity of the lacquer.
DIN and Taber 5155 Abrasion
LAT Hard Anodizing This method covers the requirements for anodization of aluminum and it alloys MIL-AF 1 Military Specification – Anodic Coatings for Aluminum and Aluminum Alloys This specification covers the requirements for six types and two classes of electrolytically formed anodic coatings on aluminum and aluminum alloys for non-architectural applications. It is intended as a means of characterizing coatings used on surgical implants.
This coating provides excellent abrasion resistance for sliding wear applications, corrosion resistance, and electrical insulation. Tape shall consist of glass spheres of a high optical quality imbedded into a binder on a suitable backing that is pre-coated with a pressure-sensitive adhesive.
This guide covers procedures for testing coil coatings. The abrasion resistance coating test shall be conducted in accordance with MIL-C Wyzenbeek — New Test Video View: Determination of Wear This Japanese Industrial Standard specifies the testing methods for determination of wool fiber integrity using an abrasion machine.
Laminate floor coverings – Elements with a surface layer based on amnioplastic thermosetting resins – Specifications, requirements and test methods. MIL-DTLF Military Specification – Plates, Tags, and Bands for Identification of Equipment This specification covers the materials and physical characteristics of plates, tags and bands identification devices used for identification of equipment. Mechanical property of film — Section 8: For purposes of this specification, foils as referred to in this specification is defined as material 0.
This standard describes a method for the determination of the abrasion resistance of organic flooring materials when exposed to walking traffic of a revolving nature point abrasion. This specification covers three types, four classes, and two forms of laminated or coated cloth.
Taber Test Methods: Taber Abraser (Abrader) – Taber Industries
Polymer modified cementitious leveling screeds and wearing screeds. Wire screen or wire mesh is used as an abradant when the test specimen is more abrasive than the cotton duck. IOS-TM Surface Resistance-Test Methods Description of a method that measures the ability of a coated surface to resist abrasive wear-through to the underlying substrate by assessing the resistance to liquid paraffin fat in the abraded area.