ASTM E1300 PDF

New Provisions in ASTM e‐ A comparison of the Basic and New Analytical Procedures for Determining the. Load Resistance of. ASTM E Standard Practice for Determining Load Resistance of Glass in Buildings Book of Standards Volume American Society for. ASTM E is the main source of technical information for architects and other design professionals to determine the right glass thickness and type to meet a.

Author: Shakazilkree Voodoora
Country: Samoa
Language: English (Spanish)
Genre: Career
Published (Last): 12 May 2006
Pages: 90
PDF File Size: 19.73 Mb
ePub File Size: 12.13 Mb
ISBN: 785-2-80037-558-1
Downloads: 56503
Price: Free* [*Free Regsitration Required]
Uploader: Yojinn

The final thickness and type of glass selected also depends upon a variety of other factors see 5. Due to the chemistry involved in the float glass process, all the colors of the rainbow are not possible. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

The values given in parentheses are for mathematical conversions to inch-pound units that are provided for information only and are not considered standard. The procedures operate under some astmm assumptions related to glass fabrication and installation, including: Appendix X1 and Appendix X2 provide additional procedures to determine maximum lateral deflection for glass simply supported on four sides.

Monolithic, laminated and insulating glass constructions made with annealed or heat-treated glass.

ASTM E – 00 Standard Practice for Determining Load Resistance of Glass in Buildings

Referenced Documents purchase separately The documents listed below are referenced within the e11300 standard but are not provided as part of the standard. Work Item s – proposed revisions of this standard. Historical Version s – view previous versions of standard.

If you see condensation on the outside of your low-e glass windows, it means the coating is working properly. This practice assumes that 1 the supported glass edges for two, three, and four-sided support conditions are simply supported and free to slip in plane; 2 glass supported on two sides acts as a simply supported beam; and 3 glass supported on one side acts as a cantilever. The resulting load resistance, which is the uniform load that a glass construction can sustain without breaking.

  MACAM MACAM TERAPI KOMPLEMENTER PDF

This practice shall not astk to other applications including, but not limited to, balustrades, glass floor panels, aquariums, structural glass members, and glass shelves. Latest Video Fun Glass Facts! Tempered glass is four times stronger than regular glass; heat strengthened is just two times stronger. Insulated Glass Units are made with two or more lites of glass with a hermetically sealed space filled with dry air or insulating gas.

For conversion of quantities in various systems of measurements to SI units refer to Practice E Thermal or insulation improvements achieved with an IGU work day and night ashm both astj and winter conditions, reducing heat entry and heat loss. In addition, considerations set forth in building codes along with criteria presented in safety-glazing standards and site-specific concerns may control the ultimate glass type and thickness selection.

Glass Education Center The single source for information on designing, specifying and building with commercial glass. Basic Design Procedures The assumptions and calculations result in these basic asm procedures that should be followed: The number of glass edges supported. It also weighs the same.

The procedures operate under some basic assumptions related to glass fabrication and installation, including:.

Invalid Email Aastm Message: The specified design load, which is the magnitude in kPa or PSF, of the type and duration of the load that is specified by the building code. The single source for information on designing, specifying and building with commercial glass.

Tempered glass deflects just as much as annealed glass. Active view current version of standard.

The center of the glass deflection will not result in loss of edge support Key Concepts that Address Wind and Snow Load Calculations There are five key concepts that impact the wind and snow load calculations on a project: Appendix X1 provides additional procedures to determine maximum lateral deflection for glass simply supported on four sides. Link to Active This link will always route to the current Active version of the standard. The assumptions and calculations result in these basic ee1300 procedures that should be followed:.

Link to Active This link will always route to the current Active version of the standard.

A procedure is also presented to calculate the probability of breakage of any annealed lite or ply see Appendix X3for short or long duration loads. Glass deflections are to be reviewed.

  EN25F80 DATASHEET PDF

If the load resistance is greater than the specified design loading and the center of glass deflection is reasonable, then the trial design is fine and can proceed.

The load share factor, which is the multiplying factor derived from the load sharing between two lites of equal or different types or thicknesses.

Astm e 1300

The values given in parentheses are aetm information only. Determination and Report of Procedures. This astk shall not apply to other applications including, but not limited to, balustrades, glass floor panels, aquariums, structural glass members, and glass shelves. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

The thermal barrier makes interior spaces more comfortable as it is easier to maintain a consistent indoor environment. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior adtm use.

For conversion of quantities in various systems of measurements to SI units, refer to SI D Practice for Plastics: About The Education Center Resources.

The word window comes from a Norse term translated “wind eye”, for “eye on the weather. Appendix X3 presents a procedure to compute approximate probability of breakage for annealed AN monolithic glass lites simply supported on four sides.

Qstm Item s – proposed revisions of this standard. IGUs reduce the likelihood of interior condensation forming by providing a thermal barrier between the inside and the outside.

Accommodating for wind and snow is one of the important upfront considerations in the design and specification process. Insulated glass units or double glazed units are a significantly more e13000 efficient glazing system than single glazing.

Designing Glass to Resist Wind and Snow Loads Accommodating for wind and snow is one of the important upfront considerations in the design and specification process. Determination and Report of Procedures.