CD4051B DATASHEET PDF

Data sheet acquired from Harris Semiconductor. SCHSD. CAUTION: The CDB, CDB, and CDB analog multiplexers are digitally-controlled . Product data sheet. Rev. 12 — 25 March 4 of Nexperia. HEFB. 8- channel analog multiplexer/demultiplexer. Fig 5. Logic diagram. An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in . Product Folder Links: CDB CDB CDB.

Author: Shasar Fedal
Country: Anguilla
Language: English (Spanish)
Genre: Sex
Published (Last): 16 November 2008
Pages: 242
PDF File Size: 9.70 Mb
ePub File Size: 3.96 Mb
ISBN: 976-2-91953-837-2
Downloads: 77412
Price: Free* [*Free Regsitration Required]
Uploader: Moogukinos

I’ve programmed a small routine that checks for consistency of the signal reading. I’ve experimented with various delay times, and 30ms seemed to improve things a lot when reading sequantially 0, 1, 2, I imagine it could be something with datashset on the ports, but I have the impression that the multiplexer is actually supposed to support very fast switching? The value then starts reading randomly. You show that you’ve got your “Signal” leads connected to the select inputs. By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service.

Datasheets search archive of electronic components datasheets

Your drawing does not correspond with the nomenclature of the chip. I’m using a breadboard of questionable quality. The CDB Output is grounded via a k resistor, so that unconnected ports read 0. Also the pulldown resistor need not be that high. Is there a better alternative?

  DISKRETE STRUKTUREN STEGER PDF

I saw a comment on the ‘arduino’ board which said that “the for loop repeatedly cycles count from 0 to 7, so [selector pins] will cd4051bb 2. Home Questions Tags Users Unanswered. Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

If I datsaheet reading random ports between 0 and 7it reads correctly for about 10 seconds, then suddenly starts reading zero. Wouldn’t the digital pins be able to sink fast enough that the IC would mux correctly? Problematic breadboards cause loose connections within the board which you cannot see and hence lead to situations such as open connections etc.

I’ve also tried adding a ddatasheet capacitor. Though this may not be very relevant in this case, its important to note that the B is a CMOS device and hence anything less than 1.

It still goes to zero. I’d try using a different board. But this happens even with 1k resistor on Input 4. Look at page 4 of this guide. Ideally something that would allow multiplexing without distorting the signal. I’m using digitalWrite on three pins to select the input port, and then waiting delay for 30ms before doing an analogRead on A0.

  CAROLINE MYSS SACRED CONTRACTS PDF

Sign up using Facebook.

(PDF) CDB Datasheet PDF Download – CMOS Analog Multiplexers / Demultiplexers

If I read dstasheet port 4 for 30 seconds, it starts to read correctly and stable. However, the control inputs require CMOS digital levels. By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

Sign up or log in Sign up using Google.

Email Required, but never shown. Post as a guest Name. I’ve tried removing the pull-down resistor.

The Arduino has datashedt 10Mohm resistance on the input side, so it shouldn’t make a difference, but the max reading was about instead of The IC has internal protection circuits. But it changes nothing. LawrenceNK1G, I’m going to read a lot of things, like pots, voltage dividers etc. That is what seems to be the source of your problems. But the documentation on their website datxsheet generally incredibly poor, so I wouldn’t be surprised.