HT12E Encoder IC can be used only with its pair HT12D. These two ICs together form an Encoder and Decoder pair. Fri, 12 Oct GMT ht12e encoder ic ht12e datasheet pdf – HT12E is an encoder integrated circuit of. 2 12 series of encoders. They are. HT12E is a series encoder IC (Integrated Circuit) for remote control applications. It is commonly used for radio frequency (RF) applications. By using the.

Author: Mikakinos Vuran
Country: Sao Tome and Principe
Language: English (Spanish)
Genre: Video
Published (Last): 26 October 2017
Pages: 63
PDF File Size: 13.76 Mb
ePub File Size: 15.80 Mb
ISBN: 363-5-92074-724-8
Downloads: 69216
Price: Free* [*Free Regsitration Required]
Uploader: Mezilkis

HT12E is an encoder integrated circuit of 2 12 series of encoders. This oscillator can be used by connecting these two pins through a 1M Resistor. The primary function of HT12E is to encode a bit and send it out through the output pin. This hr12e System-in-Package SiP integrates controller, power switches, and support components. Supply voltage; 5V 2.

They are paired with 2 12 series of decoders for use in remote control system applications. HT12E begins a 4-word transmission cycle upon receipt of a transmission enable.

HT12E Encoder IC

We should set the bits in same pattern on Encoder and Decoder IC encodder pair them. The IC has a built in oscillator. These 12 bits are divided into 8 address bits and 4 data bits. Pull the Transmission Enable pin pin 14 to ground to activate transmission. A basic connection diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting ht112e address pins to ground.


Choosing Battery for Robots. This cycle is repeated as long as TE is kept low. It is mainly used in interfacing RF and infrared circuits. These two ICs together form an Encoder and Decoder pair.

HT12E Datasheet

If you want security you can connect any of the 8 pins to 5V to make it high. Interface SD Card with Arduino. In this image I have made all four data bits as zero lowwhen this is decoded we will get the same kind of bits on the output side of HT12D, similarly we can datasyeet any changes on these 4-bits and they will be reflected on the output side of the HT12D datahseet IC.

TL — Programmable Reference Voltage.

Virgin Galactic — Commercial Space Flight. You can know to set up the HT12D after this from here. So if you are working on a project which has to transmit a darasheet data from one end to other either by wire or wireless then this IC pair will be best suited for you.

HT12E Encoder IC | HT12E Datasheet | Pin Diagram & Description

It is very important that your Decoder should also have this same address for them to talk to each other. For decoding a data the IC will requires an oscillator, luckily this IC has one in-built. This data should be sent to the HT12D for decoding, it can either be sent directly through a wire or by using a wireless medium like RF or Encodr. The Encoded 12 bit output data ht12r be obtained from this pin.


Can range from 2. In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. The 4-bit data that has to fncoder sent has to be given to the pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7.

Ecnoder put, HT12E converts the parallel inputs into serial output. Connected to the Ground of circuit. Arduino based GPS receiver. It encodes the 12 bit parallel data into serial for transmission through an RF transmitter.

This pin has to be connected to Ground 0V to enable the Transmission. HT12E has a transmission enable pin which is active ebcoder.

Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc.

SPI Module of Arduino. Submitted by admin on 30 October Choosing Motor For Robots.

Interface GPS with Arduino. What is Web Browser. The IC is has a wide range of operating voltage from 2. These are the 8-bit address bits, which is used to protect your data.