The SEX is an S series solid body electric guitar model introduced by Ibanez in It was initially produced in Korea and then later in Indonesia. There’s no way a guy who does a couple guitar setups every day of the year would do a better than someone will with instructions from the. For over 18 years, Ibanez RG guitars with Edge double locking sys- tems have been SEX MOF. • 3pc Wizard II Manually Adjustable Zero. Point System.
|Published (Last):||20 November 2015|
|PDF File Size:||15.15 Mb|
|ePub File Size:||2.2 Mb|
|Price:||Free* [*Free Regsitration Required]|
Always loosen the Stud lock screws counter clockwise with a 1.
Tighten the Stud lock screw 3. Turn the Arm torqueadjustment nut turns counter clockwise. Tighten the pressure pad screws.
For ease in retuning, it is recommended that one string at a time be changed and tuned. Retune the guitar to the proper pitch and check the angle.
Intonation adjustment is usually necessary when new strings are fitted it can also be affected by the angle of the tremolo unit. Adjusting the String Height. Height adjustment is made by adjusting the 2mm allen screws on either side of the bridge.
Raise or lower the tremolo to the desired string height using a 3mm allen wrench. Loosen the heigth adjustment screw 5 on both sides of the bridge using a 2 Phillips 2. It is sometime necessary to adjust the tremolo angle when new strings, different string gauges or different tunings are used.
Different gauges of strings can result in the need for truss rod, tremolo, action or intonation adjustment. Tremolo Angle Adjustment The tremolo system should sit parallel to the surface of the guitar body, as shown in the illustration. Solid Body Electric Guitars.
Tighten the string stopper bolt.
Loosen the Saddle lack down screw 9 on the saddle to be adjusted with a 2mm allen wrench. Loosen the string by turning the tuner and then remove the string. Use an electronic tuner and tune the guitar to a standard pitch. To change the strings angle adjust the two 2mm 6 screws on the highside of the bridge, chanding the pivot angle.
Cut off the ball end of the new string above the string winding and insert the end of the string in between the main saddle and the String holder block. Loosen the pressure pad screws on the top lock with a 3mm allen wrench and loosen the string to be adjusted.
If the 12th fret is flatter than the open note, the saddle ibqnez to be moved forward. Insert the tremolo arm into the arm socket and firmly push down until the arm snaps into place.
| Help & How To
Play the harmonic at the 12th fret, compare it to the fretted note at the 12th fret, these notes should read mnual same on the tuner. Cut off the ball end of the new string above the string winding and insert the end of the string in between the main saddle and the String holder block 4. If this happens, replace the arm bushings with new ones. Loosen the heigth adjustment screw 5 on both sides of the bridge using a 2 Phillips.
The tremolo system should sit parallel to the surface of the guitar body, as shown in the illustration. This is caused by the string vibrating.
The Overall Tremolo height can be adjusted by raising or lowering the Height Adjustment screws 5 on either side of the bridge. To check the intonation: The height adjustment of the tremolo can be set by using the two 3mm adjustment screws on either side of manhal tremolo unit. The rotation torque of the arm can be adjusted by changing the number of bushings on the arm.
TZ Bridges The Overall Tremolo height can be adjusted by raising or lowering the Height Adjustment screws 5 on either side of the bridge. Over adjustment can result in damage to the instrument and will no be covered under warranty. All guitar necks are subject to great stress as a result of string tension, humidity or changes in climactic conditions.
Thread the new string through the string holder tubeand over the saddle pulling it tight towards the headstock.